Geotechnical Engineering vs. Construction Materials Testing: Which Does Your Project Need?
· Gulf South Engineering and Testing
By Gulf South Engineering and Testing
Owners and contractors in Louisiana and Mississippi often hear "geotechnical" and "materials testing" in the same sentence, and many firms, Gulf South Engineering and Testing among them, offer both. They answer different questions at different times in a project. This guide explains what each one does, when each one happens, and how to tell which one you need right now.
What geotechnical engineering answers
Geotechnical engineering asks: what is under the site, and how will it behave when we build on it? It starts before design. A geotechnical engineer plans a subsurface investigation (borings, sampling, field tests), has the samples tested in a laboratory, and turns the results into design recommendations.
Two common sampling methods show the difference between field work and engineering. The Standard Penetration Test "provides samples for identification purposes and provides a measure of penetration resistance which can be used for geotechnical design purposes" (ASTM D1586/D1586M, section 4.1). Thin-walled tube samples "are used for obtaining intact specimens of fine-grained soils for laboratory tests to determine engineering properties of soils (strength, compressibility, permeability, and density)" (ASTM D1587/D1587M, section 5.1). The engineer decides which samples a site needs and what the results mean for design.
Typical geotechnical work on Gulf South's ENGINEERING page includes:
- shallow and deep foundations
- cofferdams and retaining walls
- slope stability and settlement analyses
- soil profiles and site geology
- shoreline and coastal protection, wetland restoration, canals and pump station foundations
- pavements, roadways and bridges, and Mississippi River facility permitting
- field work: shallow and deep soil borings up to 300 feet deep, undisturbed and SPT sampling, monitor wells and piezometers, pavement coring and water sampling
The deliverable is a geotechnical report with recommendations your structural and civil designers build on: foundation type, bearing, settlement, earthwork and pavement guidance.
What construction materials testing answers
Construction materials testing asks: did what was built match what was designed and specified? It happens during construction. Technicians test soils, concrete, asphalt and steel in the field and in the laboratory, and inspectors observe critical work as it happens.
Typical CMT work on Gulf South's CONSTRUCTION MATERIALS TESTING page includes:
- fill and base compaction and density testing, earthwork and proof-roll inspection
- concrete testing and inspection, asphalt testing, steel inspection
- pile (driven and augercast) and shaft installation monitoring, pile and shaft load tests
- vibration and noise monitoring, pre- and post-construction inspection
Much of this work follows published test methods. For example, results of ASTM C39/C39M, the compressive strength test for concrete cylinders, "are used as a basis for quality control of concrete proportioning, mixing, and placing operations; determination of compliance with specifications" (ASTM C39/C39M, section 5.3). For fill, "laboratory compaction tests provide the basis for determining the percent compaction and molding water content needed to achieve the required engineering properties" (ASTM D698, section 5.1).
The deliverable is a running record of test results and inspection reports that shows the work met the plans and specifications.
Side by side
| Geotechnical engineering | Construction materials testing | |
|---|---|---|
| Main question | What is under the site and how will it behave? | Was it built to the plans and specifications? |
| When | Before and during design | During construction |
| Typical work | Borings, sampling, lab tests, analyses | Field density, concrete and asphalt tests, inspections |
| Deliverable | Geotechnical report with recommendations | Test results and inspection reports |
| Who hires | Set by your contract documents | Set by your contract documents |
Choose geotechnical engineering if
- you are buying land or starting design and nobody has drilled the site yet
- your structure, levee, pump station, bridge or pavement needs foundation or settlement recommendations
- a regulator or permit (for example on the Mississippi River) needs subsurface information
Choose construction materials testing if
- design is done and earthwork, concrete, asphalt or steel work is starting
- your specifications name test frequencies, inspections or test methods
- piles or drilled shafts are being installed and need monitoring or load tests
Neither, yet, if
- you are still deciding whether the project goes ahead and have no site; start with a conversation about what the first investigation would involve
- your question is environmental contamination only; ask for an environmental assessment scope first
Many projects need both, in order: geotechnical work during design, then materials testing during construction. Gulf South Engineering and Testing offers both; if you use one firm for both, ask how its engineering and testing staff will share information on your project.
Frequently asked questions
Is a geotechnical report the same as a soil test?
No. Laboratory soil tests are one input. The geotechnical report combines field exploration, laboratory results and engineering analysis into design recommendations.
Can the same firm do both?
Yes. Gulf South Engineering and Testing provides geotechnical engineering and construction materials testing and inspection, from offices in Kenner, Gonzales, Shreveport and Jackson.
What standards do testing labs follow?
Laboratory tests follow published methods such as ASTM standards. Gulf South performs all laboratory testing in accordance with ASTM and/or other approved procedures.
Who should hire the testing firm?
Your contract documents decide that; check your specifications.
Sources
- ASTM D1586/D1586M-18e1, Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils, section 4.1: https://store.astm.org/d1586_d1586m-18e01.html (opened 2026-10-22)
- ASTM D1587/D1587M-15, Thin-Walled Tube Sampling of Fine-Grained Soils, section 5.1: https://store.astm.org/d1587_d1587m-15.html (opened 2026-10-22)
- ASTM C39/C39M-21, Compressive Strength of Cylindrical Concrete Specimens, section 5.3: https://store.astm.org/c0039_c0039m-21.html (opened 2026-10-22)
- ASTM D698-12(2021), Laboratory Compaction Characteristics of Soil Using Standard Effort, section 5.1: https://store.astm.org/d0698-12r21.html (opened 2026-10-22)
- Gulf South Engineering and Testing, ENGINEERING, CONSTRUCTION MATERIALS TESTING, LABORATORY CAPABILITIES and ABOUT US pages (stage 1 mirror, 2026-10-21): https://gulfsoutheng.com/engineering/, https://gulfsoutheng.com/construction-materials-testing/, https://gulfsoutheng.com/laboratory-capabilities/, https://gulfsoutheng.com/
